John Deere 544E Brake Valve
Does anyone have an idea how the left hand brake valve comes apart on this loader
View Article980m vs L220h vs wa500-7
We are in the process of buying a new loader. I was just wondering if anyone had experience with any of the above machines. We are having trouble narrowing down the 3 to just one. So just asking for...
View ArticleTrans. Oil in bellhousing
I have a Hough 65C front end loader with a DT407 engine. Yesterday when i tried to start it the starter did nothing. I pulled the rear cover off of the starter and oil ran out of it. One of the brushes...
View ArticleJohn Deere 644B -Oil in cooling system
Having some trouble with my old Deere 644B. Getting oil in the cooling system. Looks like its oil from the engine . Have replaced the engine oil cooler but nothing changed so it looks like another...
View ArticleClik here to view.
944a charging system problem old style generator
Hey Guys This is a 944a Serial # 43a4392 that has a charging system problem. I just had this post and pictures almost finished and lost it in the either. ... ( hence the shorter posts ) Attached Images...
View ArticleClik here to view.
944a charging system problem old style generator
Hey Guys This is a 944a Serial # 43a4392 that has a charging system problem. I just had this post and pictures almost finished and lost it in the either. ... ( hence the shorter posts ) Attached Images...
View ArticleNeed Help! 1996 John Deere 8875 boom and bucket shuttering when hot
hi guys I need opinions... I have a John Deere 8875the model is from 1996 the motor runs strong and the machine is still tight has way too many hours for the meter to read and a horrible repaint on it....
View Articleold trojan model 124 trouble shifting
my friend acquired this lovely loader we think its a 124. it has a ih264 gas motor . its having a lot of trouble shifting and staying in gear. where do you check the trans fluid in this, ive looked all...
View ArticleCase 1530b Uni Loader Main drive bearing replacement
Hi, New to this forum and wondering if anyone has info on Case 1530b Uni Loader Main drive bearing replacement ? We disconnected the chains but can't lift high enough to get at bearings - anyone know...
View ArticleParking brake won't release
2010 842 liugong loader. The parking brake won't release when we depress the button. We replaced the button switch and the solenoid. It worked fine for a week and now it is doing it again. I check all...
View ArticleCAT 924G brake pressure light comes on briefly when braking?
Lately the brake pressure warning light on the dashboard comes on very briefly. Sometimes it's just enough to see the red light light up, sometimes it's a little longer to make a little beep. Never...
View ArticleBobcat 873 hydraulic problem
I have an 873 Bobcat with high pressure going to the low pressure side of the system, can anyone tell me were to look for the problem? I have blowen 2 coolers!
View ArticleChinese wheel loaders
Hi partners, I want to know the estimate of the Chinese wheel loaders,Who can tell me, if you know, please let me know, I think almost person did not use it ,
View ArticleTrojan 114 trouble shifting into high range
I recently purchased a 1970 trojan 114 with backhoe attachment. I can get it to run 1st and 2nd in low range but can't get anything in high range this is my first loader so I'm learning a lot any help...
View ArticleNeed some HELP....make that lots of help
I got a hold of an old 55-AG Michigan series 1 about a 60 to 62 model. Serial 2BC046. Both hydraulic pumps need to be rebuilt/replaced. The lift/dump is a Hydreco and don't know if that is the original...
View ArticleVolvo 220E Wheel Loader Only Starts With Ether
Hey guys, new here. My 4 co-workers and i man the garage for a small family owned quarry op. We work on all types of stuff, bosses lawn mower, Mack dumps, catapillar end dumps, rock drill, forklifts...
View ArticleTorque converter oil
Does anyone know what oil the torque converter on a 55A Michigan uses. Thanks:usa
View Articlegehl 5635sx
I am looking at buying a 2000 Gehl 5635sx with 7000hrs on it. The deutz engine was rebuilt around 4000 hrs. Is that an overly large amount of hours, and will parts start wearing out alot now? I have...
View Articlejohn deer 544B wheel loader
Hey guys,, anyone out there have any dealings with an ole 544b wheel loader, ive got one that is giving me hyd issues dealing with the bucket up an down function, my customer has an loader with forks...
View ArticleJohn Deere 544k tilt cylinder drift issue
Brandt just installed new tilt cylinder on loader, but did not fix the problem. when loaded and close to ground grapple creeps down. only creeps when there is a load on it and its close to the ground....
View Article