Looking for a super heavy duty sweeper for a cat 928
So both sweepers we have arnt holding up they are down more then they are up. Does anyone know of a extreme duty loader mounted sweeper? We have two a cat and one from Volvo both are too light for the...
View ArticleAnother weak 544
I just acquired a 544. Drove it 15 miles home and by the time we got there it barely would climb a hill in low range. The oil pressure is right at the mark at high idle, the oil temp warmed up to right...
View ArticleWheel bearings on a JD 544
Are the wheel bearings on the axles on the 544 isolated from the axles lube fluid? The parts diagram makes it look that way. Are you greasing the bearings when you put grease into the ends of the axle...
View ArticleFiat allis 645B hyd pressure
Guys - anyone know what the hydraulic pressure should be on a Fiat Allis 645B. We built a grapple for it and don't seem to have much clamping force so we got checking and are only getting about...
View Articleterex 70c
help i need to find parts for the brakes on my 70c wheel loader i need the complete pressure converters or master cylinders and I'm not sure where to get them. I'm in canada alberta so i would like to...
View ArticleJCB loaders vs others.
We are looking to upgrade our 15500 hour 544e loader. looking at a size larger like a 938 624 721 ect. I ran across a nice 2005 jcb 436 with low hours. How do they compare with a cat deere and case....
View ArticleClik here to view.
Help identifying skid steer hydraulics
Hi Everybody! I've just purchased an old German skid steer loader model name : Lanz Zetcat LL 30/2. My problem is, that I can't find much information about this machine on the internet. Since it's...
View ArticleCat 988b tranfer gear oil leak please help
Hi guys im new here i want thank for accept me in this forum, now i explain my problem. i have a 988b and have a very strong oil leak in front of transmission, (under cabin) y already changed more...
View ArticleIT24 Electronic Issues?
I'm trying to pin point or at least narrow down a few areas to check - my IT24 does not have accessory power in the cab when the key is in the on position and the main switch is on, it starts up fine,...
View ArticleCat 938K vs Volvo L90G vs. Komatsu WA320-7
Ok wanted to get a new thread going on a specific topic. We have decided to get two sizes of wheel loaders in this next purchase. We are convinced we need some smaller units for broom work as well as...
View Article1990 trojan o&k 3500z transmission fluids
I'm having a hard time finding out if the transmission fluid in my trojan 3500z is hydraulic fluid or transmission fluid.. I can't find a service manual anywhere.. I would almost assume it would be...
View ArticleBacklash and preload settings on differential
Anybody has the backlash value and preload setting values of a clark differential of a Michigan 55C
View Article966 steers slow to the right
I just bought a 966C that steers slow to the right, works fine to the left but is slow turning to the right. It does not make a diffrence if you rev it faster, doesn't labor the engine, almost seems...
View Articlecase 1835c driving me nuts
Tmd20 with stanadyn injection pump. Starts very easy and runs for about 3 seconds and stalls. Will start right back up and do the same thing.. Any ideas would be great
View Articleclark michigan 85 III wont go forward
I was about to buy this loader and have test drove it several times. I was going to buy and drive home (only 3 miles away) so I was playing with brakes trying to see if I could get them to work when it...
View Article821C tans bolt removal/newbee
I cant get the bolt out of the transmission on the 821C. Ive tried breaker bar, heat, freeze, hammering you name it. Can I take a bolt out of the lower housing on the tranny and drain it that way?...
View ArticleJD 544B Replacement engine
Somebody replaced the engine in our 1979 544B, the numbers do not match up with the original serial #'s that were given to me by JD, the present serial # starts with ME3TB and ends with 174726T, this a...
View ArticleIT28G Hydraulic problems
We are having trouble on our IT28G with the impliment hydraulics. When you let the boom down to the ground it will fall way faster than it should (cycle time of 2 sec when it should be 4 sec) and when...
View ArticleVolvo L90E burning oil and lots of it
This lady has only 20K on the clock and suddenly started burning 3 litres of oil per 10 hour day. Changed the oil . I had a spare turbo so I put it on. Made no difference. Did valve seals and valve...
View Article