Volvo L70F Lifting gear creeping?
Hi folks,I have a Volvo L70f with the lifting gear creeping slowly. Have changed both ram lift ram seals but problem remains. The machine is fitted with boom suspension. just wondering if anyone has...
View ArticleMichigan L320 NO Forward
Will low brake pressure or air in the brake system cause the declutch to engage- There for no forward and If so how do we fix- Already replaced Input clutch seals and rebuild modulator valve. Worked...
View ArticleFinding a cab for a 624K John deere Loader
Hi, does anyone know where i can buy a new cab for our 624K loader? does John deere sell them directly or do i have to go through a dealer? who makes them for deere? can they sell me one?
View ArticleMy allis 940 loader is sick,i need some advise
Folks,I have a yr 72-74 Allis 940 loader. I had some problem with loosing torque converter motion today and upon checking tranny oil fluid level i found the level to high and the ATF fluid was...
View Articlescoopmobile information please
I have a scoopmobile 3 wheel loader-model hp? late 70's early 80's. it has a 300 six ford engine and funk transmissions, one auto- one 4 speed. it has worked near daily for the past 8 years--haven't...
View Articledresser 530 & 550 good or bad ?
looking at 2 loaders one a 530 and 1 550 do they have problems i have heard that trannys are weak link any ideas thanks
View Articlewhat is this, can anyone help me???
does any one know what is countershaft gearbox and planwtary gearbox? Thanks. Can you please forward pictures for my reference?
View ArticleDoosan DL 550-3
Hi everyone, anyone here who already has some experiences with this machine, or older big Doosan loaders?
View Article910E wheel loader transmission started to delay shift forward & reverse
I have a CAT 910E 1989 wheel loader for use on my acreage at my house. While plowing snow yesterday, April 19 and plowing snow!, the loader started to (the first time I noticed it), to slowly engage...
View ArticleMichigan 125a
Hi i have a 1970 Michigan 125a wheel loader rear wheel steer. machine started moving sluggish so I changed and checked the trans fluid, didn't seem to do much. then one day i went to move the machine...
View Articlecase 921c front axle removal and build
Has anyone removed the front axle on a 921c. I am trying to figure out if I can remove it without having a crane. I was thinking possibly jacking the machine up high enough so that when I remove the...
View ArticleO&K Trojan 5500
Hello just wondering if anyone has one of these Gems and would be willing to take a picture of your relay wiring and send it to me. I am in the process of rewiring the machine and the only diagram in...
View ArticleCat 914G Loader only goes 8Km/h
Hello, I just bought a 1998 Cat 914G loader with 18000 hours on. Nearly all electrics are in dismay. The loader only drives about 8Km/h while all other hydraulics function perfectly. I believe that the...
View ArticleCase W24 B
I just picked up this case w24b and i want to change the drive shaft seal in the TT2421 allison transmission,It leaks when the loader is shut off but not when working.Its the seal behind the park brake...
View ArticleJD 544 trans oil type?
Wondering what type oil is a 544 loader tranny supposed to have in it? Have had this loader for 10 years and in winter months have to let warm up at least 20 to 30 minutes before it will move.It had...
View ArticleI have a big GOOD CONDITION PC800-7 excavator for sale, anybody like it?
I have a big GOOD CONDITION PC800-7 excavator for sale, anybody like it? Place of Origin Japan Model Number PC800-7 Condition Used Year 2010 Make Komatsu Operating Weight 800000kg Bucket capacity 3.4m3...
View Articlenew holland lw80B center pin
Has anyone removed the center pin, having a time with it. About to start up the torch. Thanks
View Article950G II, machine security key lost
Hi guys, I'm currently working on a 950G II wheelloader with MMS (machine security system) installed, though the engine ECM was bad and has been replaced and re-programmed but the machine could not...
View Article966f series 1 boom dropping
have had a 966f series 1 with an intermittent boom drop problem. so operator goes into pile backs out with bucket full, if you hold up on joystick boom will lift, when you let go it returns to center...
View ArticlePettibone-Mulliken
Hi, does anyone know about old Pettibone loaders? How heavy was the biggest model and was that PM-560? I haven't found much information about these wheelloaders, only couple of pictures. Tom
View Article