721 d won't crank
The 721 that we changed the injectors on will not crank at all now. All fuses are good, we get a crank signal to the relay going to the starter but no power to the relay to switch it over. Both of...
View Article544k transmission slipping
Hello operator was complaining about our 544k having no power. Engine jumps right to 1800 but feels like trans is slipping. Is there a calibration to the clutch PAC? Seams I remember doosan mechanic...
View ArticleDoosan Wheel Loaders?
Hi Guys. My family has a large farm. We are looking at getting a new wheel loader. We are looking at deere, cat, and doosan. I must say the Doosan looks very nice. I wanted to ask your guys opions of...
View Article930 won't when cold?
Howdy, we have an older 1970s vintage 930 wheel loader that has to sit an idle 30 min before it will move. It developed this problem a couple of months ago and I just thought the oil was super cold....
View Article1988 Cat 988B
Hello Everyone My loader runs out fine in all 4 gears, but when I go to dig, push or load the bucket the drive seems to slip. Is this a torque converter issue? There is no grinding sounds or jerky...
View ArticleCummins Repower
Hi Guys, my first post on here after lurking for a while and soaking up some of your knowledge. I was contacted today by a customer who has two Komatsu wheel loaders W600 and W700 that have broken...
View Articlehelp ( caterpillar 950g wheel loader)
Hey guys, I'm new here. I need help with 950G wheel loader , i found this fault code on ECM implement 950 352-13 Lift Lever Sensor : Out of Calibration 358 -5 Implement Pilot Pressure Supply Solenoid...
View ArticleFord A 64 tt2221-1 Allison tranny issues
Hi i have a Ford A 64 with an Allison TT22221-1 Trans in it. My problem is there is almost no power in the 2nd gear, Its like the clutch or torque converter is slipping or not working. In first gear,...
View ArticleLw130.b problems transmission
I have a new holland lw130.b loader it starts and seems to drive ok but when you push in to the dirt it seems like it is slipping in the trans. Wheels don't spin. Oil does not smell burnt. Filters and...
View ArticleHough 90 Alternator
Anyone know offhand what model alternator is on the hough 90e #2094 International engine DT573 I know its a delco but not sure on any numbers. Or any other reason this machine won't charge. It is up in...
View Article2003 it28g
Our IT28G wont start, but when started she will not go int any gear on either of the gear selectors (Joystick or gear stick). Seems like the reason she wont start is because she is in gear on the...
View ArticleVolvo L220E 2005
Hi , looking for some help on a L220E. machine was working fine. Carried out a full 2000hr service, all filters all fluids as per Volvo amounts on service sheet. i now have the yellow central warning...
View Articlewa-480 komatsu transmission cut off problem
WA 480-6 Komatsu .We are having a problem with the transmission cut off,works a few minutes then stops working.Getting code DHT1KX. Komatsu dealer changed cut off sensor,by passed harness from...
View ArticleCat 910 Wheel Loader. Drive problem
I've a pretty old 910 loader (80U2873). When I start up, I've got reverse, neutral, 1st, 2nd and 3rd gears. after a short time (2 or 3 mins or a few gear changes) I lose ALL drive. I've replaced all...
View ArticleInternational 560 engine swap
Hi I recently purchased an International 560 loader with an IH817C bad engine. It has a broken timing gear which sheared the key on the crankshaft and bent several valves and pushrods. I'm finding...
View ArticleVOLVO L90 Loader random intermittent stalls
Hey guys my crew are having problems with our L90 loader. the issue is that the engine will randomly cut out, to get her going again you must select neutral and turn the ignition off. she will then...
View ArticleCat 980B Whines
Hey guys I just purchased my third 980B. It a decent machine but it whines. For sure when you turn it when going along. Also at times with the hydraulics. Any ideas where to start? Thanks
View ArticleClik here to view.
Case B & C wheel loader Steel Light Housings NOT PLASTIC 521b 621b 721b 821b...
The mounting post is heavy reinforced steel C Channel. But the housing "gaurd" that bolts to it is plastic that gets more fragile with age and cold weather. Don't pay $120 (part #L126951) for a couple...
View Article1960s Allis Chalmer Tl-14D After 5 Minutes Won't Move
I traded work for a 1960s vintage Allis Chalmers TL-14D. After 5 minutes the forward clutch pressure drops from 200psi to less than 100psi and it won't move. For the first 3 minutes I can spin the...
View Articlejohn deere 744J
Gda'y People, new to the forum, am looking at buying a 2nd hand John Deere 744J, has 8500hrs. there isn't much Deere gear on the market in Australia so was wondering if anyone new much about them? what...
View Article