Deere 644E brake issue
My boss asked me to figure out a problem with the John Deere 644E loader that he just bought. It started out as a slight "shudder/groan" from the right front axle while applying the foot brake. Soon...
View Article644J Shifting & Display problems
We have a John Deer 644J Loader. For a few months now, the dash display has been going on and off sporadically. When it goes off, the wheels must be at a complete stop before it will shift forward or...
View ArticleClark 275b
Need help figuring out what year my Clark 275b is serial number is 425b-427 thanks
View ArticleBuilding a Michigan 675
Don't know if ya'll are into this, but saw a Clark 475b loader in an auction so I was reading about them. Found this, thought it was cool. https://www.youtube.com/watch?v=0-rVHgOorKM
View ArticleCase 621 CXT
Hi All, I just purchased a 1999 Case 621 CXT with 8k hours. I have never owned anything Case before but the price was right. Any opinions on the machine, any problems to look out for? Thank you!
View Article1975 case w 14 wheel loader lost hyd. On boom and bucket
Hello fellas this is the same loader that I was asking questions about the brakes a few lines below. I hooked up the air motor--installed belt- and it built up some pressure in the system. There are...
View Article624j transmission leak
have transmission oil leak coming from weep hole under torque convertor housing. Have taken torque convertor out and resealed pump several times. Even replaced pump and torque convertor because of...
View ArticleHyundai 740-3 ride control accumulator
Hi, have a Hyundai HL 740-3 with ride control that needs the Hydac piston accumulator resealed. Would anyone know what pressure the accumulator needs to be recharged to? It doesn't say on the tube of...
View ArticleAustralian 'Mine Spec' Loaders!
Hi all, My farming property is located within a very rich Gold and Mineral producing area of Victoria, Australia. Being that my principle source of income is Primary Production, I also hold several...
View ArticleKomatsu wa320-1 losing brakes over night
Working on a komatsu wa320-1 and every morning we have to refill the brake reservoir and bleed the brakes the mastereo cylinder was rebuilt by the previous mechanic when this problem first came up so...
View ArticleVolvo L90E black smoke for no obvious reason
I have done the piston rings and bigend bearings and a good hone at 20K hours . It had been burning a gallon of engine oil a day for the last 500 hours . The oil rings were bad so that was the problem...
View ArticleCan extra hydraulics be added to a case loader????/
I have a Case W 14 Payloader--it is a 1975. There is one hyd. lever for the boom and one for the bucket. Can another unit be added so that I could run one two way hyd. cylinder. Also on these old...
View ArticleGehl skidloader starts but wont stay running or throttle up
my gehl 7810 skid-steer will start and kinda idle for a bit but then will kill. If I throttle it up it also kills. It kinda throttles up a little on its own the kills off or almost kills seconds.
View ArticleBrake conversion help
I have a 91 2000Z I was thinking bout converting the brakes. We always have issues with the calipers its a snow machine. I know there must be some other caliper that would work??
View ArticleQuestion about low hour machines.
Looking at machines for sale, there are a few with very low operating hours compared to the age of the machine; a hundred or fewer operating hours per year of machine age. It's very attractive to see a...
View ArticleClik here to view.
Help Identifying Model of this Old Euclid/Terrex Loader
We just bought this beauty (clearly we need to replace the motor the guy we bought it from has a replacement we got in the deal we just have to install it.) 9 But we are trying to figure out exactly...
View ArticleHyundai HL730TM Questions
Just bought a HL730TM-3 and haven't gotten it back to the shop yet from the auction and have a few questions.... I am not at all familiar with 24v systems and this loader has the charging light on the...
View ArticleVolvo l70c hot oil
Hi have a problem with an l70c heating the hyd oil. When the loader is idling the hydraulics are under load, whilst idling if you pull a lever and the loader starts to move the engine actually revs up...
View ArticleCat 980F Series, No 2nd Gear
I have a 980F that is used on a farm that has lost 2nd gear in forward and reverse. I would like some advice on possible causes, and the amount of time needed to remove and repair if necessary. Thanks...
View Articledanrodda
Hi Fellas, wondering if anyone has had any issues with a Cat 980B loader with very low torque issues in first gear forward and reverse? Seems to be getting worse, it does get better once it heats up...
View Article