2000 Komatsu WA450-3MC
Anyone have a wiring diagram handy for a WA450 Ser. A31067? Intermittent loss of power to ignition switch fuse. Thanks!:beerchug
View ArticleCase W18 Steering issues
Hello, We have a Case W18 loader from late 70's early 80's. Machine was a county machine and we have owned it a while. Only has about 1700 hours but the years are making for repairs here and there. Of...
View ArticleCat 950G float feature problem
We have recently bought an older 950G loader 5MW series. It appears to have the bucket float feature; push the boom lift lever forward and it "floats" the bucket. The problem is it won't automatically...
View ArticleCat 950G rear differential slack
The same old 950G 5MW series we just got the hydraulics working properly on, also has a drive line noise. The machine drives well, no excessive noise while driving at speed, diff oil is clean, but when...
View ArticleHough loader 65c
What would cause a diesel leak coming out of the top of the injector pump when running?
View ArticleCat 924 G trembling articulation, why?
Hello to everyone, it´s my first time on this forum and starting asking for help. Last week I bought a used Cat 924G, year 2000. Among a few things I could repair by myself, I noticed that the...
View ArticleCat 924G slow hydraulics
Recently our 2001 cat 924G seems slow on hydraulics. When lifting a full bucket into a dump trailer I need to rev the engine pretty hard to make it lift. On idle if I pull the cross lever back, I feel...
View ArticleForestry tires
I wanted to see if anyone has any experience with forestry tires on a wheel loader for water and sewer work. We have had a real wet year and major issues getting the loaders around the site. We have...
View ArticleBobcat 763 hydrolic issues
I was useing my 2000 bobcat skid 763G splitting wood like I have been doing a lot recently for winter when my bucket lift and tilt quit working. I have unhooked my splitter attachment and started...
View Articleused parts for a michigan loader
I am having a hard time finding used parts for a Clark Michigan 75B Loader. I need a planetary drive for front axle. Any help would be appreciated.
View Articleold volvo loader
Hi, I'm after some parts from a 1970's volvo LM 1641 loader. In particular, I'm after a set of ZF diff centres. I would really appreciate someone pointing me in the right direction. thanks tony
View ArticleClik here to view.
New to me Michigan loader
Hello all, This is my first post an the forum and my first purchase of heavy equipment. My father has had old backho's and stuff but never any wheel loaders. I set out looking for a dozer but found...
View ArticleClik here to view.
Clik here to view.
New to me 950f loader
In all her sweet glory a 1995 950f loader Ive seen this machine since new this machine was always just a backup machine it had only abouy 3k hours machine is super tight only has rust from sitting...
View ArticleCat 980F Series, No 2nd Gear
I have a 980F that is used on a farm that has lost 2nd gear in forward and reverse. I would like some advice on possible causes, and the amount of time needed to remove and repair if necessary. Thanks...
View ArticleClik here to view.
Dresser 550 32L Question
I was hoping someone could help me with information on my wheel loader. I traded a guy for a Dresser 550 so I can clean up my property. I was wondering if anyone knew where I could find service manuals...
View ArticleWA 380 Komatsu A/c problems
:BangheadSo operator tells me ac blowing hot and both of his condenser motors are not turning. Did a quick check all fuses are good no power at both the condenser pig tail while a/c on. Does anyone...
View ArticleClark 175b House Routing
I am need of some advice REAL BAD. I'm still working on getting this Clark 175b wheel loader. I am replacing the control valve inside the cab. It has six hoses that was attached to it. I removed it a...
View Article2002 Case 621 D
I have a Case 621 D we use it mostly in the snow. I went to get it ready for transport back to the shop for maintenance before the season starts. when I got there the unit wouldn't start. it would turn...
View ArticleHough H 60
Hi Guys, I have a hough h60 I been working on most of the summer. I got everything reconditioned on and almost ready to go. I knew it needed a front shaft carrier bearing thought I would do that last....
View Article