Kobelco LK1150 help
Hi all, I'm new to this forum and recently acquired an early 1990s Kobelco LK1150 front end loader with a cummins turbo 6 engine. Motor runs excellent but I am nervous about a few leaks I noticed. One...
View ArticleWA 500 Komatsu A/c blower motor
:Banghead WA 500 Komatsu A/c blower motor not working. I have power at the 6 wire prong pigtail. I believe orange is hot when fan is to be on and when a/c button pushed on, the orange and red wire are...
View Articleloader volvo 4400 BM re-wireing solenoid valve coils
Hi, I'm new to this forum so sorry if this is not the place to post this problem. Our loader stopped going into gear and it ended up being a whole lot of old bare wires behind the switches touching and...
View Article3204 pump timing in 926 cat...nige?
94Z1377 machine sn, 45v49216 eng sn, 3204. I'm swapping pump and parts of of new long block and was wondering the procedure to either lock in the pump to swap or to set the timing upon installation. I...
View ArticleCASE W14 Starter Issue
First off thanks for the add. We have a 1981 W14 Case with a 1985 motor conversion. The converted motor is a 100 HP Cummings. The issue we are having is that we are going through starters every couple...
View ArticleCase 621 experts out there? I just bought a C model and hope it's not...
Hi everyone, I just bought a 1999 621C it has 7700 hours and was used for logging and has some sort of log grapple on it. The pivot pins for the attachment are worn out center link has been broken and...
View ArticleCat 924 G neutralizer override
Hello, does anyone know what is this button for? because when it is activated on my loader, nothing changes. In my oppinion, shouldn´t the loader be stopped getting forward whitout any torque, while...
View ArticleNeeding a 4-5 yard loader
I am looking for a loader for a new gravel business to load truck and move material around pit. I don't have a lot of cash so what would a good start up loader be? Are there any brands out there to...
View ArticleDresser 515C - Trouble Uphill
I am having trouble with loader making it up hill with any power/speed. On flat ground loss of power does not seem great. This is a 1995 Dresser 515C picked up used, new engine/swap around 2006. It...
View ArticleBrakes on a case w14 payloader 1975
Wanting to check out the brakes on the loader. Removed the rear wheel , but the brake drum does not just come off. There is more tear down. Any of you fellas been into this type of job. Thanks for any...
View ArticleWa 500-6 series Komatsu Steering Problem
:Banghead The steering issue on this loader is that when you press down on the brake pedal and hold it there, and then you turn the steering wheel. The steering wheel will turn freely, but the front...
View ArticleL120E steering shudder problem
Hi i have a Volvo L120E and quite often when trying to turn the steering jerks heaps, you start turning then it will stop start stop start etc.. it does it in both directions. does anyone have any...
View ArticleCat 972G not moving
Hi guys, I have a 972G and wosnt moving after some minor repairs were done. had an extra machine down serial numbers are 1 off, engine was blown. swaped that trans over and cab. Started it up and doing...
View Article87 Dresser 530
Hello, Does anyone know where I can get some of them 4 inch lights in a 28 volt. Checked all over. Thanks in advance.
View Article1972 645b wheel loader reverse problem
I don't know If anyone could help me ,I was using the loader to level some gravel like many times before . I was usingi it in reverse backing up when it stop moving suddenly,I had lost my hydrolic...
View Articledeere 644g serial number location
hello everyone, we have a john deere 644g wheel loader that has a missing serial number tag. i was wondering if anyone knew where it would be stamped else where. talked to dealer they said i would have...
View ArticleClik here to view.
CAT 962G (3BX) selenoid current increase abnormally
Hi everyone, I have a problem on a CAT 962G. Lower selenoid current increase instantly to 100% value after reaching 75%. Please look at the attached picture. I try to move gradually lower lever and at...
View ArticleAllis-chalmers 840B wheel loader torque convertor oil leak
Any one have experience with the torque convertors in an AC 840B loader? Ours just runs oil out of the bell housing. Pulled the motor twice and replaced all the orings and seals. Can't see any cracks...
View ArticleCA3 latest firmware update file???
Hi Where can I get the latest firmware file for CAT CA3 thank you
View Article544d stripped down cab...parts????
Hello, Thinking about buying a 544d, the cab has been stripped down somewhat and I'm worried about getting the small parts that will make it comfortable.....like a door!!!! Any good wrecking yards,...
View Article