Clik here to view.
This could make a good snow pusher.
Visibility isn't great but I bet its strong enough!! Brakes are still smushy, but that's a weak pilot/brake pump. Next goal is to rebore the lower center pin. Attached Images Â
View Article930 CAT brake problems
On the loader operator they are too brake master cylinders that are on the right side looks like they have breather filters and fluid is leaking out of them brake fluid. Does this mean both brake...
View ArticleEther or no ether. 644E
so the 644E has an ether start button but it looks like its fallen into disrepair. the instructions say crank for 1 second, pause, gas it and crank it again. It seems to start with a little protesting...
View ArticleFirst post, thanks in advance! Deere 544B radiator help
New guy here, who has a ton to learn! I have acquired an old 1979 or 80 (I think) Deere 544B loader that has extensively rebuilt 5 years ago and not used or even run since. My buddy was the machinists...
View ArticleWa450-3 parking brake issues
So, this last week I was running my 450, using it to load a manure spreader. I'm a one man show right now, so I would load the spreader, then shut off the loader. It would typically take me 12-14...
View Article972k blown EGR
972k s/n 0972KHZ4W00657 last monday plastic coolant tank sprung a leak in the top got it replaced found a recall had to wait two days on it from cat. we replaced filled with coolant cranked engine...
View ArticleSplit the deere!
so the lower pivot pin is fubar! has nearly an inch of fore/aft play between the loader frame and the pivot. The pin itself through the engine frame looks pretty tight overall. The upper pin seems to...
View ArticleInstalled new Hyd. Pump, hydraulics have been drifting ever since...?
The hydraulic pump on our 980G recently went bad, so we replaced it with a new pump straight from our Cat dealer. As soon as it was installed both the tilt and lift have been drifting quite noticeably....
View Article1998 IT28G trans problem
I need some help. I have a 98 IT28G loader. It will intermittently go into neutral in forward or reverse. When it does it you have to shut it off and restart it. It might keep doing it or it might not...
View ArticleMichigan 55B questions?
Hi guys, New member here! I picked up myself an Michigan 55B loader a while back and have a few questions. Pretty sure it's an 1977 model going by the serial # V378 Cummins. First off everything seems...
View ArticleCat 950g
Hi can anyone help our cat 950g won't start the engine try's to turn over but it's clicking whilst trying to start as if it was the starter motor we've changed that and we've still got the same fault...
View ArticleHough International H-70 Loader
Hough International H-70 L60-70-80-90C 74621 I need a little help figuring out where to check the transmission fluid level? It also has 2 levers on the steering column, one works forward and reverse...
View ArticleHough International H-70 Loader - Steering
Hough International H-70 L60-70-80-90C 74621 Repacked both steering cylinders do to leaking. Steering is still very tight and slow. Have to bring the rpms up high and move the steering wheel slowly for...
View ArticleClik here to view.
Clark Michigan 175C Loader Only moving in reverse
I am trying to get this thing operating after sitting for several years. I don't have any history/info on the machine. Engine is running and moving in reverse but I have no forward. I have read that...
View ArticleJohn Deere 444c hard steering
Hello, I'm working on a John Deere 444c. The machine is very hard and slow to steer both directions. The wheel turns hard, and the machine very slowly turns, like its trying to catch up to how far I...
View ArticleWa500-3le sn a70001-up
Hi everybody. Who has shop manual of KOMATSU WHEEL LOADER WA500-3LE SN A70001-UP ? Please send it to hamed.shamsikhani@gmail.com Thank you.
View ArticleGrease Zerks
Hi there, I am wondering if you guys could take this short survey about grease zerks. I am working on my high school engineering project and need some statistics and research. The survey deals with...
View ArticleDoosan DL200 TC
Wondering if any body has a Doosan loader and what there thoughts are on it.
View ArticleCAT 988G Wiring schematic??
Hey cat guys, im dealing with a 988G, No horn (tested switch and all is good), but when the lights are on the horns sometimes work on their own, so customer has ran w/ horns disconnected. Also radio in...
View Article