MF-33 wheel loader
Can anyone help me find a repair kits for the transmission control valve on a model 2420 52 clark transmission in a MF-33 wheel loader. I also need a repair kit for the pressure regulating valve on the...
View Articlewa250-3
hi guys i have a komatsu wa250-3 loader and the transmission is filling up with hydraulic oil...i had a mechanic check it out and replace the seal in the hyd pump but to no avail...it seems to fill...
View Article2007 John deere 444j axle flush
We just bought a John deere 444J, Both axles haven,t had the oils changed for a long time, oil samples were bad, got it at good price, So I want to flush both diffs, what is the best way to flush...
View ArticleBobcat 773 hydraulic problem
Ok as said in the title we have a hydraulic problem on our bobcat 773. The bobcat runs fine and drives fine but the tilt and raise will not work. Its like it is not disengaging. The bar that you pull...
View ArticleCat 924gz
I had a problem 924gz wheel loader can not be running, cat dealer has been replacing ECM, FIP and harnes GP. the supply of fuel are met, test nozzles ok but the engine still can not start
View ArticleIh 540a
Hello Me need specification (model torque converter TWIN DISK) International harvester Wheel loader 540A (Payloader) Any help is appreciated
View ArticleCase 1845 wheel bearing nut torque
I have one wheel bearing apart and am waiting for the new bearings and seals from Motion. I don't have a rebuild manual. My question is what should the bearing preload or endplay be? What is the...
View ArticleCase 1845 maintenance manual sources
I have a Case 1845 for which information and parts are getting scarce. Any suggestions where to find a maintenance / rebuild manual? Thanks ***oops; I found the right forum Moved to compact equipment...
View ArticleJD 544A Steering Problems
When steering the machine it will turn fine to the right, but from a right hand turn you go to articulate left and it turns fine until the machine is straight and then slows down and sounds like it is...
View Articlecase loaders
Does anybody out there have experience with Case wheel loaders ?Especially C series
View Article621 case forwward reverse lever
so yesterday got to try my new loader out it is a 1991 case 621 it worked great except for the forward reverse lever a couple of times when i went to go to back up it wouldn't shifted it into neutral...
View ArticleWill a 3306B engine work in a 980B cat loader?
I own 3 Caterpillar 980B loaders. They all run and work just fine. I'm always looking for spare parts and can get a 3306B engine cheap. What are the differences? Are the internals the same? I'm sure...
View ArticleOil analysis interpretation , to buy wheel loader help?
I am looking at buying a John Deere 544h With 16000 hrs on it. The machine came out of TX its fairly tight, no corrosion pretty clean. The price is not horribly bad but not a steal by any means. Only...
View ArticleKomatsu wa 380 loader wont move parking brake light stays lit all the time
My loader wont go into forward or reverse. The parking brake light wont go off. It has had this problem but after moving the parking break switch back and forth it finally goes. Not any more. I took...
View ArticleCat 924g problem
serial number 9sw01157 I think I'm right last 2 digits are screwed up .. Anyway it doesn't go into to 4 th gear code is 681-2 irradic signal ,no signal ... I tested the high speed solenoid and no...
View ArticleMachine total fluid capacity. Math not working well
So, I'm working on a 644E loader, the spec seems to say 30 gallons for hydraulic system capacity, 6 gallons each axle and 4 gallons for the trans, numbers rounded off. So with the axles filled and...
View Articlebobcat
I have a 763G bobcat that has triangle lights on front the panel says input I get nothing to work want even do codes for me I crank it by the fule serlinoid on the back of motor by pressing it forward...
View ArticleClik here to view.
trademarks and historical machines forget
sorry if I open this thread, but among the historic cars that are part of the museum exhibits of technology hough I should mention, I think you would ancestor dresser and international biographical...
View ArticleI need technical support
Hello everyone iam new tho this site and I really hope that i ca benefit you guys see i have this problem we have hunday wheel loader model HL 757-9SM after it worked 1800hrs the service indicator...
View Articlecase 24c loader transmisson oil
Would anybody know what weight and type of transmisson oil I should use in my case 24c loader, it is currently low and would like to use it in morning. TIA
View Article