Cat 824F rear axle
I have a Cat 824F wheel loader with worn rear axle pivot bushings; what is best way to do this repair? Roll the axle out from under frame or remove support pieces and work in place. I assume the axle...
View ArticleCan I use a CAT 966K in a enclosed building
Did anybody use a CATERPILLAR 966K in a underground job or in an enclosed building , how can I avoid regeneration problems
View ArticleVolvo L90E half shaft
Has anyone else halved a half shaft on the back of one of these ? Does any one in western Europe have one ? What are the odds of the other one snapping in the next 1000 hours? Is a used one a waste of...
View Articlecenter pins
Hi everyone, I have a small 2011 John Deere 244J wheel loader, has 2,000 hours, when does one replace center pin(s), im new to this type of equipment but always see used equipment for sale here and...
View ArticleCat 930G boom lowering issues
I have a 930G w about 7000H on it, it has no ride control, was an intermittant issue until recently. You can lift the loader arm all the way up and when you go to lower the arm it goes about 2 feet and...
View ArticleVolvo L120E EECU PSID 096
At work, we've got a 2006 Volvo L120E w/ a D7LAE3 that is leading me on a bit of a chase. It is throwing a code for the PSID 096 which Volvo is telling me is a lack of fuel and shuts off. I can have...
View ArticleWA500-3 no boom down
Got an issue with my loader. Boom goes up fine, but will not go down until it drops into float then crashes. I swapped pilot lines around, disconnect the ride control, replaced suction valve, reseated...
View ArticleJCB 409 Brake problem
HI, can some one help me please i had a problem with JCB 409 compact wheel loader Brake the rear Axel brake had no signal so the loader brake too week just the front brake work > can some one give...
View Articlevolvo L120F 3rd 4th gear
dear all i have problem with volvo L120F the 3rd and 4th gear not working please , can you help me with that. i have this flout code below in the display : SE 2702-4 IECU RE 06-5 VECU THANKS FOR ALL
View ArticleClik here to view.
which is the biggest and the big powerful wheel loadern
Hi guys today I would like to propose a survey of opinions among you professionals and specialists in earth moving industry veterans if you should give your opinion between the caterpillar 994, the the...
View ArticleCan a diesel engine "vapor lock"?
Numbers first. Cat988H S/N BXY00384 Engine C18 S/N RHX00979 Electronic Unit Injectors. Engine starts fast in morning but when shut off for break or lunch when restarted 15 minutes later starts good...
View Articlecat 924F electrical problem
I have a CAT 924F that blows the 1st fuse on the left hand side of control panel ; it has the battery symbol above it. the wire coming out of the fuse is a yellow wire with the number 120 printed on...
View Articlevolvo l50d
Extremely low engine power. Rpm good at no load. Does not smoke under load. Any ideas would be helpful
View Article950g tranny problems!
i have a 2001 cat 950g that will not shift in auto everytime it shifts to 2nd gear it pops right back to first. when i do it manually works fine one thing i noticed when i change the selector 1-4 the...
View Article950F Manual Parts
Hi guys, my name is Eduardo. I need the "950F Manual Parts". I live in Argentina and I can't purchase it on ebay/amazon/internet, because the government does not allow transactions in dollars...
View ArticleAllison TT transmission?
Help! I am the proud owner of one of those elusive Timberjack 1500 C loaders made by Eaton in the middle 70's. It has some transmission issues and I was told it had an Allison tranny in it....
View ArticleSamsung SL120-2 questions/reliability
Hello all, I'm new to the forum but have been trying to research before I asked you folks some questions. I'm looking at a loader (Samsung SL120-2) for snow removal purposes mainly. Small yard work for...
View ArticleLW130 wipers and heater stops working
I have New Holland LW 130. When turn on wipers or heater there is click sound and they stop working. Can wait few min and turn back on and both will run a few seconds then click sound and stop. I'm...
View ArticleQuick Hitch Ram , Komatsu wa380-6
I have the piston and rod seperating, I had the thread re-done on a lave, re-assembled ram with loctite and nwe wipe seal. That was last week and it looks like it has done the same thing again, Any...
View Articleas you maneuver an earthmoving machine tricks to safely maneuver the various...
hello guys I am a fan of earth moving machines often use to handle scrap loaders and telehandlers cat of course, since I am not a professional you are novice could you give me tips thanks? there would...
View Article